Warning

You are reading an old version of this documentation. If you want up-to-date information, please have a look at 5.0 .

3. Results

../../../_images/qualification_overview.png

Fig. 132 Qualification Results

This page uses all the collected information and displays it as a summary of all the runs that you performed in the previous step. Then, it allows you to adjust some parameters to simulate a production timeline.

Note

The very first image acquisition as well as the the first vibration aren’t taken into account in the calculation.

Run Statistics

The run statistics are a reflection of the recipe performance based on the qualification runs.

Tip

These statistics are really useful to identify the bottlenecks in the recipe.

Tip

You can add more runs by going back to the previous step (all previous data is kept).

Good parts

../../../_images/qualification_results_good_parts.png

Fig. 133 Run Statistics - Number of good parts

The chart displays the evolution of the number of good parts detected over all qualification runs.

The average value of this metric over all qualification runs is displayed below, as well as its minimum and maximum value (in brackets).

Tip

When no good parts are found, an additional vibration sequence is required. This has a critical impact on the robot waiting time.

Time to first part

../../../_images/qualification_results_time_first_part.png

Fig. 134 Run Statistics - Time to first part

The chart displays the evolution of the time the system took to find the first good part over all qualification runs.

The average value of this metric over all qualification runs is displayed below, as well as its minimum and maximum value (in brackets).

Note

This metric directly reflects how optimized your vision recipe is.

Tip

To improve it, consider reducing the number of bad parts reaching the candidate selection step and masking all unnecessary features on the pick-point and pick-angle teaching steps.

Fill percentage

../../../_images/qualification_results_fill_percentage.png

Fig. 135 Run Statistics - Fill percentage

The chart displays the evolution of the fill percentage measured by the image analysis over all qualification runs.

The average value of this metric over all qualification runs is displayed below, as well as its minimum and maximum value (in brackets).

Part distribution

../../../_images/qualification_results_part_distribution.png

Fig. 136 Run Statistics - Part distribution

The chart on the right side displays the distribution of the parts between accepted and rejected for each qualification run.

The chart on the left side displays the average distribution over all qualification runs.

Tip

Use these charts to identify what step of the recipe could be improved.

Distribution of good parts

../../../_images/qualification_results_distribution_of_good_parts.png

Fig. 137 Run Statistics - Distribution of good parts.

This chart displays the distribution of the number of good parts measured during the qualification runs.

Note

If the vibration sequence is longer than the robot cycle time, the robot will be waiting between each vibration sequence. The average number of good parts per run gives an indication about how frequently this waiting will occur.

Tip

When no good parts are found, an additional vibration sequence is required. This has a critical impact on the robot waiting time.

Cycle Time Simulation

This section combines the qualification runs with the theoretical robot cycle time and anticipation percentage to simulate a production timeline.

Use it to assess what impact would the vibration sequence and image analysis have on your production timing.

Robot cycle time

In order to compute the simulation, the robot cycle time must be entered. This value can be changed to monitor the impact on the pick rate and the robot wait.

../../../_images/qualification_results_robot_cycle_time.png

Fig. 138 Illustration of the robot pick and place cycle

Anticipation Percentage

Also linked to the robot is the anticipation percentage. It represents the share of the cycle time as a percentage where EYE+ is allowed to vibrate/take a picture to improve performance by working while the robot is still moving. As the name suggests, this percentage refers to the last X % of the cycle time, where X is the anticipation percentage. For example, if you set this value to 20% with a cycle time of 1000ms, EYE+ will be able to vibrate/take a picture after 800ms (the last 20%).

../../../_images/timeline_0_anticipation.png

Fig. 139 Timeline with 0% anticipation

../../../_images/timeline_65_anticipation.png

Fig. 140 Timeline with 65% anticipation

In the figure above, as an anticipation percentage of 65% was chosen, the red arrow is exactly 65% of the blue one (1300ms vs 2000ms).

Note

Changing this percentage after performing a single run produces no differences to the data as there won’t be a next vibration to anticipate.

Pick Rate

../../../_images/qualification_results_pick_rate.png

Fig. 141 Cycle time simulation - Pick Rate

The pick rate is calculated using the data from the qualification runs and will vary when changing the robot cycle time and anticipation percentage.

The average, minimum and maximum values are displayed above the graph.

Timeline

../../../_images/qualification_results_timeline.png

Fig. 142 Cycle time simulation - Timeline

The timeline contains two different tracks, the top one is about the robot while the bottom one is about EYE+. The robot track shows when the robot gets a response to a get_part command with a vertical bar. Each bar on the same continuous line is separated by the value of the robot cycle time, which you can set using the dedicated field.

The EYE+ track shows when the connected Asycube ran a vibration sequence, its duration as well as all vision events, including when an image was captured or when the coordinates of a good part were ready to be transmitted to the robot using the get_part command.

Tip

You may zoom/pan on the timeline to focus on specific points in time using your mouse.