Avertissement

You are reading an old version of this documentation. If you want up-to-date information, please have a look at 5.1 .

What performs vision calibration?

What are the corrections made with the checkerboard?

  • Correct image distortion: Once the calibration is done, each time an image is acquired, the distortion will be automatically corrected.

    Note

    For more information about what distortion is and how it is corrected, refer to the section Distortion correction.

  • Define the region of interest (ROI): The ROI is the residual region of the images that will be used later for any image analysis. It is a way to reject image regions that are not used for image analysis:

    • The left and right sides of the images always include regions outside the Asycube.

    • If in your integration, the same part of the image is always hidden by another device (hopper, robot, lights, …), this part will be automatically rejected from the ROI.

    Important

    For this reason, make sure you have the same system integration that you will have during production to ensure rejection of undesired regions of the image.

    Do not disassemble your hopper, robot, lights (etc…) to get a better calibration result! This may cause image analysis errors when editing recipes or during production.

    In Fig. 120, the ROI is the green rectangle surrounding the checkerboard.

  • Determine the pixel-millimeter or pixel-inch scale: The origin and orientation of the vision system coordinate does not change (Fig. 162). The system coordinate before vision calibration goes from 0 to 2048px in x and from 0 to 3072px in y. The system coordinate after vision calibration goes from 0 to the image height in millimeters/inches and from 0 to the image width in millimeters/inches (Tableau 31).

    Tableau 31 Vision change of coordinate

    Before calibration

    After calibration

    Reference

    X

    Y

    X

    Y

    Point 1

    0

    0

    0

    0

    Point 2

    2048px

    0

    Height

    0

    Point 3

    0

    3072px

    0

    Width

    Point 4

    2048

    3072px

    Height

    Width

    ../../_images/vision_origine.png

    Fig. 162 Vision system coordinate

Distortion correction

The main goal of the vision calibration is the distortion correction.

Distortion is a monochromatic optical aberration that results in a variation of magnification in the image for a fixed working distance. A checkerboard image subjected to distortion will produce curved lines instead of straight lines (left checkerboard from Fig. 163).

../../_images/distortion.png

Fig. 163 Optical distortion correction (left: before calibration, right: after calibration)

Distortion does not technically reduce the information contained in the image, as it only displaces the information geometrically. This means that the distortion can be effectively calculated from an image and therefore corrected without losing much information.

A distortion model is determined by looking for the distortion parameters and the parameters of the intrinsic and extrinsic properties of a camera to fit the checkerboard lines of the distorted image. The model attempts to reconstruct the curved lines. Once these parameters are found, the distortion correction transformation can be applied to the distorted image.

Note

The distortion correction transform is a mathematical operation, based on the distortion parameters, applied to the image. It will be applied to each image acquired, before performing any image analysis.

The Fig. 120 shows an image of the checkerboard before (left) and after (right) the distortion correction. The detected checkerboard corners are represented by green crosses.

RMS error

In the step 8. Camera configuration results, we provide you with the root mean square error (RMS) of the distortion reconstruction. This is the average error between the expected checkerboard and the checkerboard resulting from the distortion reconstruction. The closer the re-projection error is to zero, the more accurate the parameters we have found.

Avertissement

If the RMS error is greater than 1, the correction is not applicable.

Note

The checkerboard is also used to determine the pixel-millimeter or pixel-inch scale presented in result step 8.

Parallax correction

By providing the height of the camera in step 6 (the working distance), the system will be able to correct the parallax effect when you will provide the height of the part during recipe edition.

../../_images/parallax_correction.png

Fig. 164 Left: Before parallax correction; Right: After parallax correction; Pick point described by the yellow target

Parallax is a difference in the apparent position of an object viewed along two different lines of sight. For EYE+ applications, the 2D image of the parts from the camera’s point of view can introduce a perspective between the top and bottom surface of the parts if the parts are high and are far from the Asycube center. The top surface is offset from the bottom surface. This phenomenon introduces a shift of the picking coordinates. The higher the part, higher is the parallax.

In the situation presented in Fig. 165, the parallax produces a displacement to the right of the upper surface of the cylinder with respect to the base of the cylinder (right cylinder) from the camera’s point of view. The variation in Y due to parallax is the distance e between the yellow point (real position) and the red point (position detected by EYE+: this position is shifted due to perspective). The yellow point is the corrected position of cylinder center projected on the camera plane (horizontal black dashed line).

../../_images/parallax.png

Fig. 165 Parallax correction of a cylinder (left: top view, right: side view). Yellow point: real picking position; Red point: position detected by EYE+ without parallax correction.

Astuce

Try to imagine the resized image of the lower plane (horizontal black line) projected on the camera plane (dashed black line). The image is resized of R to remain in the vision cone.

../../_images/parallax2.png

Fig. 166 Lower plan (horizontal black line) projection on camera plane (horizontal black dashed line) view from the top. The projection is resized by ration of R.

EYE+ corrects the parallax effect induced by the variation of the position of the parts on the surface of the Asycube by adding an offset on the X and Y coordinates of the part according to its position on the Asycube plate. A part located on the edge of the plate will have a greater offset than a part located in the center. To calculate these offsets, the system needs to know the height of the part and the height of the camera.

Note

The parallax correction is not performed when configuring the camera but later, when you will provide the height of the part to the system for the calculation of the coordinates.