Warnung

You are reading an old version of this documentation. If you want up-to-date information, please have a look at 5.0 .

4.2 Pick Point Positioning

../../../../_images/pick_point_teaching_pick_point_positioning.png

Abb. 73 Pick Point Teaching - Pick Point Positioning

Enter the part height

The part height you must enter in this step is the height where the pick point is placed.

EYE+ corrects the parallax effect induced by the variation of the position of the parts on the Asycube surface by adding an offset to the X and Y coordinates according to its position on the platform. A part located on the edge of the platform will have a greater offset than a part located in the middle. To calculate these offsets, the system must identify the height of the part where you specified the pick point.

../../../../_images/pick_point_teaching_part_height.png

Abb. 74 Part height depending on the pick point position

Bemerkung

In the case of custom or structured production plates (with holes, grooves…), the part height entered must be adapted to not take into account the height of the part located inside the plate.

../../../../_images/pick_point_teaching_part_height_special_plates.png

Abb. 75 Part height depending on the production plate used

Enter the production plate height

Similar to the part height, EYE+ also needs to account for the thickness of the production plate used with the current part in order to correct the parallax effect. For a standard Asyril plate, this is the distance between the bottom of the plate and its surface as described on Abb. 76 for a standard Asycube 240 plate.

../../../../_images/pick_point_teaching_production_plate_height.png

Abb. 76 Height measurement for a standard Asycube 240 production plate

Per default, EYE+ will set this value to the height of the standard Asyril production plate for your Asycube type as defined in Tab. 22.

Tab. 22 Default production plate heights

Asycube

Height (mm)

50

6.0

80

6.0

240

13.0

380

12.5

540

12.5

If the current part requires a special plate, you will need to measure the height of this plate as described in Abb. 76 and enter the value in the production plate height field in EYE+.

Pick Point Positioning

Carefully place the target target on the desired pick point position. This operation must be performed carefully because it determines the accuracy of the coordinates (X, Y) that will be sent to the robot.

Tipp

Use the drawing tools to set the pick point precisely.

../../../../_images/pick_point_positioning_drawing.png

Abb. 77 Pick Point Positioning

Bemerkung

The coordinates returned by the get_part command will be directly corrected with the offset of parallax if the camera configuration has been done properly.

Feature masking

../../../../_images/pick_point_positioning_features_masking.png

Abb. 78 Feature masking for the positioning of the pick point in the middle of the circle at the maximum height of the part

The objective of the feature masking step is to define the reference features (residual features after masking) that will be used as a model to place the pick point.

Not all features are relevant to define the reference model.

  • Features at the same height: Features that are not placed at the same level as the pick point must be masked out. We only want to detect as accurately as possible those features that are at the same height as the pick point. Adding features that are not at the same level may alter the accuracy of the positioning of the pick point due to parallax (these features on a different level will not always have the same relative position depending on the position of the part in the Asycube).

  • Reproducible features: It is essential that the reference model reflects a general description of the candidates. Any features that are not reproducible from one candidate to another must be masked.

  • Enough feautures: There must be enough features to ensure that there is only one possible pick point identified by the algorithm. For example, if you want to pick the part in the middle of the circle but you do not inform the system about the circle features, there will be two possible pick point positions.

    ../../../../_images/not_enough_features_example.png

    Abb. 79 Not enough features to position the pick points: 2 possibilities

Use the brush brush to mask undesired features.